¶ Disclaimer
Please read this manual carefully before using the Carvera. Failure to read the manual may lead to personal injury, inferior results, or damage to the Carvera products.
This manual is provided for reference purposes only. We reserve the right to modify or revise this manual, users can download the most up-to-date version of this manual on our website.
Carvera is equipped with multiple sensors (Motor stall sensor, Spindle abnormal sensor, etc.). However, you should always pay attention in operation that milling cutters revolving in high-speed, unstable components or laser in operation are dangerous to people without protection. Please carefully read the safety instructions below to avoid unnecessary casualties.
¶ Safety Instructions
1. Always wear safety goggles when operating Carvera, especially when the protective cover is open.
2. Always wear laser protection goggles when using laser function.
3. Please wear hearing protection when Carvera is machining on the hard materials.
4. Do not put your hands close to the spindle or machining area. Keep the protective cover closed when operating Carvera.
5. Do not leave your Carvera unattended while it is machining.
6. Please be aware of the sharpness of the milling bits during installation, dust collection, and other operations.
7. Milling and laser carving will generate heat. Inappropriate parameters will cause fire hazards. Make sure an extinguisher is in your vicinity.
8. Some materials are harmful to people when machining or laser craving, such as carbon fiber and epoxy resin. Please wear a face mask and turn on the automatic dust collection.
9. Do not expose this machine to rain or wet conditions.
10. Keep children and bystanders away while operating this machine. It requires supervision and the assistance of an adult when children use this machine.
If an emergency occurred in machining, such as the workpiece being loose from holding, components damaging, unusual light or sound coming from the machine, etc. Press the main button or E-Stop button, all ongoing procedures will stop immediately, or cut off the power to shut it down. Carvera is built by closed-loop servo motors, and it saves the coordinates and status at each step. Therefore, no need to recalibrate after reboot, just restart the job.
Carvera has a safety option that allows the machine to automatically stop working when opening the cover, which is useful for schools or work environments where children may reach.
¶ FCC Compliance
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio / TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
¶ ISEDC Compliance
This device complies with Innovation, Science and Economic Development Canada License exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any interference received, including inter ference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil nedoit pas produire de brouillage, et(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure nd compliance. The minimum distance from body to use the device is 20cm.
Le présent appareil est conforme Après examen de ce matériel aux conformité ou aux limites d’intensité de champ RF, les utilisateurs peuvent sur l’exposition aux radiofréquences et compliance d’acquérir les informations correspondantes. La distance minimale du corps à utiliser le dispositif est de 20cm.
¶ Safety Labels
